Kitchenaid KUD01 User Manual

TECHNICAL EDUCATIONKUD01STAINLESS STEELDISHWASHERJOB AID 4317288KAD-748Inc.For the way it's made.™

396CANCELING A CYCLEAnytime during a cycle press:The display shows:The dishwasher starts a two minute drain (if needed.) The wash pump does not opera

38 72. Check the detergent dispensers. They must be filled properly for the new cycle.3. Close the door.4. Press a new cycle and/or options.5. Press

378Delay HoursSelect this option to run the dishwasher at a later time or during off-peak hours. Items can be addedany time during the delay countdow

369CYCLE STATUS INDICATORSThe progress of the dishwashing cycle can be followed with the Cycle Status Indicators.Add Rinse AidWhen the RINSE AID EMPTY

3510FUNCTION DESCRIPTIONThe washing action of the KitchenAid KUD01 Stainless Steel Dishwasher performs more work andmaintains higher performance with

3411Drain Function1. During the Drain function, a separate drain pump motor (1) is started while the main washpump motor continues to operate for 1 mi

331221Automatic Purge FiltrationThe Automatic Purge Filtration feature may be invoked if the soil sensor detects excessive soils. Thiscan occur durin

3213SECTION THREECOMPONENT ACCESSCOMPONENT LOCATIONInner Feed TubeMiddle SprayArmWater InletDrain TubeHeatingElementFloatDoor Latch AssemblyElectronic

3114ACCESSING COMPONENTS IN THE DOORRemoving the Console PanelThe control panel on the KitchenAid KUD01 Dishwasher comes in two versions: a) Split Con

3015Removing the Electronic Control BoardThe electronic control board on the KitchenAid KUD01 Dishwasher is virtually the same configurationfor both t

INTRODUCTIONThis Job Aid, KUD01 STAINLESS STEEL DISHWASHERS, Part No. 4317288 provides specific infor-mation on the operation, diagnosis and repair of

2916Removing the Active VentAssemblyThe Active Vent Assembly is located in the con-sole area.1. Remove the six (6) screws securing thecontrol panel to

2817Removing the Dispenser AssemblyThe Dispenser Assembly is located in the lower portion of the dishwasher door below the consolearea.1. Remove the e

27183. Rotate the rear feed cap (Fig. 3-11a) ¼ turn clockwise (Fig. 3-11b)Fig. 3-11aFig. 3-11b4. The entire inner water tube assembly and the lower sp

2619-- NOTES --Servicing the Overfill AssemblyRemoving the Overfill Control SwitchThe overfill control switch can be removed fromthe overfill assembly

2520Removing the Sump AssemblyThe entire sump assembly can be removed from inside the dishwasher tub.1. Remove the access and toe panels fromunderneat

24 21Removing the Wash Motor1. Remove the bolt securing the washmotor and drip shield in place on the pumpassembly. (Fig. 3-20)2. Once the bolt and dr

2322Accessing Components in the Sump AssemblyComponents inside the sump can be accessed without removing the sump from the dishwasher tub.1. Remove th

TABLE OF CONTENTSSection OneINSTALLATION CONSIDERATIONS ... 1GENERAL CONSIDERATION...

45WHAT TO DO IF THE DISHWASHER DOOR DOES NOT OPENIf the door latch assembly is damaged or malfunctions, the dishwasher door may not open. If thisoccu

1SECTION ONEINSTALLATION CONSIDERATIONSGENERAL CONSIDERATIONSFor complete installation procedures see the “Installation Instructions” in theliterature

2-- NOTES --43MODEL SPECIFIC TABLESKEYPAD MATRIX8268477MODELNO.PRESSURESWITCHDISPENSERRINSEAIDSENSORRINSEAIDHARNESSWIRINGHARNESS82699968269189 8269190

3SECTION TWOTHEORY OF OPERATIONCONTROL PANELSMODEL KUDI01TJ - 6” ConsoleMODEL KUDM01TJ - 6” ConsoleMODEL KUDR01TJ - 4” ConsoleMODEL KUDS01IJ - 4” Cons

4CYCLES AND CYCLE VARIATIONThe KUD01 dishwasher optimizes washing performance and efficiently uses resources by varyingcycle functions and length. The

5Quick Clean UpUse this cycle for pre-rinsed or lightly-soiled loads. The cycle automatically adds a fill and brief pre-wash, purging cold water from