KitchenAid KVUB600DSS Use and Care Manual download pdf (Page 8)

3. To wire through wall:

Mark a line distance “A” from the left of the centerline on the

wall. Mark the point on this line that is 1" (2.5 cm) from the

bottom of the cabinet. Drill a 1¹⁄₄" (3.2 cm) diameter hole

through the rear wall at this point.

Style 1 - Cut Openings for 3¼" x 10" (8.3 cm x 25.4 cm)

Rectangular Vent System

Wall Venting

To make a 4" x 10½" (10.2 cm x 26.7 cm) rectangle in the wall:

1. Make 2 lines by measuring 2³⁄₄" (7.0 cm) and 6³⁄₄" (17.1 cm)

down from underside of cabinet and mark on the centerline

on the back wall.

2. Mark lines 5¼" (13.3 cm) to the right and left of the centerline

on the wall.

3. Use saber or keyhole saw to cut a rectangular opening in the

wall for the vent.

Style 2 - Cut Openings for Rectangular to 6" (15.2 cm)

Round Vent Transition

Roof Venting and non - vented (recirculating)

To make a 6½" x 8½" (16.5 cm x 26.7 cm) rectangular cutout

on the underside of cabinet bottom:

1. Mark lines ½" (1.3 cm) and 7" (17.8 cm) from the back wall on

the centerline of the underside of cabinet.

2. Mark lines 4¼" (10.8 cm) to the right and left of the centerline

on the underside of cabinet.

Use saber or keyhole saw to cut a rectangular opening for vent.

To make a circular vent opening on the underside of the

cabinet top:

1. Mark a centerline on the underside of the top of cabinet.

2. Mark a line 3³⁄₄" (9.5 cm) from the back wall on the underside

of the top of cabinet.

3. Use a compass or a circle template to draw a 6¼" (15.2 cm)

circle.

4. Use saber or keyhole saw to cut the circular vent opening.

Non-Vented (recirculating) Installation Through the

Soffit/Cabinet

Measure and mark the centerline of the cabinet to the soffit

above.

Measure from the bottom of the cabinet to the centerline of

the where the vent will come through the soffit. Mark the

location and use a saber saw or keyhole saw to cut a 5¾"

(14.6 cm) hole for the vent cover.

Install Vent System

1. Install vent through the vent opening in cabinet or wall.

Complete venting system according to the selected venting

method. See “Venting Requirements” section.

2. Use caulking to seal exterior wall or roof opening around the

cap.

Install In-Line Smart Kit - Optional

NOTE: Your range hood can work with either an internal or an in-

line (external) blower motor system. An optional In-Line Smart Kit

(purchased separately) allows the blower motor that comes with

this range hood to be installed in a location other than inside the

range hood cavity.

CAUTION: To reduce the risk of fire and electric shock, install this

range hood only with the In-Line Smart Kit manufactured by

Whirlpool, Part Number W10692945.

For installation see the In-Line Smart Kit installation instructions.

See the “Assistance or Service” section to order.

A. 12" (30.5 cm) for 30" (76.2 cm) models

12¼" (31.1 cm) for 36" (91.4 cm) models

Centerline

1" (2.5 cm)

2¾"

6¾"

Cabinet

front

(7.0 cm)

(17.1 cm)

5¹⁄₄"

(13.3 cm)

Centerline

5¹⁄₄"

(13.3 cm)

4¹/₄"

(10.8 cm)

4¹/₄"

(10.8 cm)

*7"

(17.8 cm)

*From wall, not cabinet frame

*¹⁄₂" (1.3 cm)

A. Vent cover

B. Centerline

Circular vent opening

Cabinet

cutouts

*From wall, not

cabinet frame

*5"

(12.7 cm)

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 31 32

Comments to this Manuals

No comments

KitchenAid KVUB600DSS Use and Care Manual Page 8

Comments to this Manuals

Related products and manuals for Cooker hoods KitchenAid KVUB600DSS