INSTALLATION INSTRUCTIONS30" (76.2 CM) FREESTANDING AND SLIDE-INELECTRIC RANGES INSTRUCTIONS D'INSTALLATION DE CUISINIÈRES ÉLECTRIQUES AUTOP
10 Assemble a UL listed strain relief in the opening. Feed the power supply cord behind the black horizontal cross brace and through the strain reli
114-wire connection: Power Supply CordUse this method for: New branch-circuit installations (1996 NEC) Mobile homes Recreational vehicles In an a
122. Use ³⁄₈" nut driver to connect the neutral (white) wire to the center terminal block post with one of the 10–32 hex nuts.3. Connect line 2 (
13Bare Wire Torque SpecificationsAttaching terminal lugs to the terminal block - 20 lbs-in. (2.3 N-m)5. Use a hex or Phillips screwdriver to connect t
14Verify Anti-Tip Bracket LocationIMPORTANT: On models with a warming drawer, the rear range foot must be viewed from the front and slightly to one
15If removing the range is necessary for cleaning or maintenance:For power supply cord-connected ranges:1. Using two or more people, slide range onto
16SÉCURITÉ DE LA CUISINIÈREEXIGENCES D'INSTALLATIONOutillage et piècesRassembler les outils et pièces nécessaires avant de commencer l'insta
17Pièces nécessairesLors de l’utilisation d’un cordon d’alimentation électrique : Utiliser un cordon d’alimentation électrique homologué UL pour util
18Dimensions du produitCuisinière autoportante*La cuisinière peut être surélevée d'environ 1" (2,5 cm) en ajustant les pieds de nivellement.
19Dimensions du placardLes dimensions de l’espace d’ouverture entre les placards correspondent à un plan de travail de 25" (64 cm) de profondeur,
2TABLE OF CONTENTSRANGE SAFETY ...2INSTALLATION REQUIREMENTS...
20Spécifications électriquesSi les codes en vigueur le permettent et qu’un conducteur distinct de liaison à la terre est utilisé, on recommande qu’un
21Mesures pour une hauteur appropriéeCuisinières coulissantes :1. Mesurer la hauteur du plan de travail jusqu'au sol aux 4 emplacements correspon
22Avant de déplacer la cuisinière, la faire glisser sur sa base d’expédition, sur un carton ou un panneau de fibres dur. 1. Enlever le gabarit de la t
23Réglage de l'aplomb de la cuisinière1. Placer la grille dans le four. 2. Placer un niveau sur la grille et contrôler l'aplomb, d'abor
Déplacement de la cuisinièreLorsqu'on déplace la cuisinière, la faire glisser sur une planche de carton ou en de fibres dur pour éviter d'en
3INSTALLATION REQUIREMENTSTools and PartsGather the required tools and parts before starting installation. Read and follow the instructions provided w
4Mobile Home - Additional Installation RequirementsThe installation of this range must conform to the Manufactured Home Construction and Safety Standa
5Cabinet DimensionsCabinet opening dimensions shown are for 25" (64.0 cm) countertop depth, 24" (61.0 cm) base cabinet depth and 36" (9
6*The NEC calculated load is less than the total connected load listed on the model/serial rating plate.**If connecting to a 50-amp circuit, use a 50-
7 This range is equipped with a CSA International Certified Power Cord intended to be plugged into a standard 14-50R wall receptacle. Be sure the wal
8Freestanding Ranges:1. Measure the distance of the countertop to the floor.2. Then measure from the top of the range cooktop trim to the floor.3. You
96. Align anti-tip bracket holes with holes in floor. Fasten anti-tip bracket with screws provided.Depending on the thickness of your flooring, longer
Comments to this Manuals